bitelog.ukAll articlesHome

How to Read an Avionics BITE Log: A Practical Guide to Making Sense of Fault Data

Updated 16 November 2026

Every modern line-replaceable unit (LRU) keeps a record of what it thinks has gone wrong. When a crew reports a problem, that record is often the best evidence you have. Pulling the log is usually the easy part. Making sense of it is harder.

This guide covers what BITE data is, why fault logs are hard to read, and a straightforward method for working through one. It applies whether you're looking at a satcom SDU, a modem, an antenna controller, a datalink radio or any other LRU.

What BITE actually is

BITE stands for Built-In Test Equipment. It is the self-monitoring logic inside an avionics unit. It checks the unit's own hardware, software and interfaces, then records anything outside expected limits.

Most units run several kinds of test:

The results go into a fault or event log. Depending on the unit, that log may hold timestamps, flight phase, fault codes, status words and sometimes free-text messages.

Why raw fault logs are hard to read

A BITE log is written for the unit and its designers, not for the engineer standing at the aircraft at 3am. A few things make it difficult.

Hex fault words

Many units record faults as hexadecimal status words. Each bit, or group of bits, means something different. A single value such as 0x0042 might stand for two separate conditions at once. Decoding it by hand means finding the right table in the right revision of the documentation, then working through it bit by bit. That's slow, and easy to get wrong.

Boot-up noise

Units often log a burst of faults every time they power up. Interfaces aren't ready yet, peer systems haven't come online and timers haven't settled. These entries are usually normal, but they can look alarming. In a long log they can easily outnumber the entries that matter.

Knock-on faults

One real failure can set off a chain of secondary faults. A lost power rail or a dead data bus might cause a dozen other monitors to report errors. If you chase the loudest or most frequent code, you can end up treating a symptom rather than the cause.

Intermittent faults

Some of the hardest problems come and go. One entry in isolation tells you little. A pattern across several flights, or a link to a particular flight phase, can tell you a lot. Seeing that pattern means reading the whole log in context, not just the most recent entries.

A practical method for working through a log

No method replaces the unit's approved documentation, but a consistent approach saves time and cuts down on guesswork.

  1. Start with the reported problem. Write down exactly what the crew or previous shift reported, plus when and in what flight phase. This is your anchor. Every entry you look at should be judged against it.
  2. Confirm the unit and its configuration. Note the part number, modification standard and software version if you can. Fault code meanings can change between versions, so decoding against the wrong table gives you the wrong answer.
  3. Set aside the start-up entries. Find the power-up sequences in the log and mark the entries you'd normally expect to see there. Don't delete them, but don't let them steer you either.
  4. Line up the timeline. Find the entries that fall around the time of the reported event. Faults that appear at the right moment carry far more weight than ones from weeks earlier.
  5. Look for the first fault, not the most common one. In a cascade, the earliest entry is often closest to the root cause. Ask whether the later faults could simply be consequences of the first.
  6. Check for patterns across flights. Do the same codes come back on every sector, only at altitude, or only after a cold start? Repeating patterns point towards intermittent hardware, wiring or environmental causes.
  7. Form a likely cause, then verify it. Once you have a likely explanation, check it against the approved troubleshooting data before acting. The log points you in a direction. It doesn't make the decision for you.

Common pitfalls to avoid

PitfallWhy it causes trouble
Replacing the unit that logged the most faultsThe fault may sit elsewhere, such as a peer system, wiring or power, with this unit just reporting it.
Using the wrong revision of the fault tablesBit meanings can differ between software or hardware standards.
Reading only the last few entriesIntermittent faults and early root-cause entries get missed.
Treating start-up faults as real failuresThis leads to unnecessary removals and wasted effort.
Not recording what you foundThe next engineer has to start from scratch if the fault comes back.

That last point matters more than it seems. A short note on which entries you ruled out, and why, can save the next shift a lot of time.

Where a log analyser fits in

Much of the work above is mechanical: decoding hex, filtering start-up chatter and lining up timestamps. It's necessary, but it isn't where an engineer's judgement adds most value. That's the gap BiteLog is built for.

You pull the BITE or event log off the unit and tell BiteLog which unit it came from. Then you add the aircraft and what was reported. BiteLog reads the whole log against that unit's technical documentation and returns a structured result. That result includes:

It also offers batch processing and PDF export, plus a team history. You can use a personal login or a shared team login, and each account only ever sees its own logs, never another team's.

One point to be clear about: BiteLog is a diagnostic aid only. Its output is not approved maintenance data and not a release to service. The cited sources are there so you can check each finding against approved data before you act. That keeps the final decision where it belongs, with the engineer.

What it costs

There's no subscription and no setup fee, and you get a 30-day free trial from your first login. After that, you pay per analysis, based on the work involved:

Prices exclude VAT. Charges are totalled into one itemised invoice on the last day of each month. Full details are on the pricing page.

Get started with BiteLog

If decoding fault words by hand is eating into your troubleshooting time, you can request an account on the BiteLog analyser page. Use your own name or a team name so your whole team can share one login. New accounts are checked before they're activated.